Qom, Mahmoudabad Industrial Town, Phase 3, Resalat Street, Alley 42, Chemfix Company
By utilizing cutting-edge global knowledge, expert professionals, international collaborations, and a fully equipped laboratory, chemFix has succeeded in offering its products to the market with superior quality and competitive pricing.
rial6.210.000
For bonding various types of tiles and ceramics to tiles, concrete, cement, natural and artificial stones, public restroom floors, staircases, parking lots, factories.
For tiling on surfaces directly exposed to water and moisture.
Suitable for both indoor and outdoor installations.
Ideal for tiling in high-traffic areas.
The amount of adhesive required depends on the condition of the substrate (porosity and unevenness of the surface) and the tile grooves. On average, the consumption is approximately 2.5 to 4 kg per square meter.
The surface to be applied must be firm, clean, dry, and free from dust and loose particles. Any loose paint or coating should be removed before applying the adhesive. This adhesive can be used for leveling, smoothing, and correcting minor surface imperfections up to a thickness of 5 mm. It is necessary to allow adequate drying time (at least 48 hours) before proceeding.
Mix the powder with 3.5 liters of clean, non-mineralized water until a smooth, paste-like consistency is achieved. Once mixed, allow the mixture to rest for 5 minutes to thicken. Use a notched trowel and the double bonding method to spread the mixture evenly on the surface and the back of the tile.
Use uniform tapping or slab shifting to remove any remaining air between the surface and the slab.
After 48 hours of installation, you can proceed with grouting. During this period, avoid applying pressure to the installed material.
If installing over old tiles, at least two-thirds of the old tile’s glaze must be scratched before installation.
If installing on gypsum surfaces or light blocks, ensure the surface is properly prepared, and a primer is applied before installation.
Before starting, use a screed and level to mark the surface’s unevenness and level it with a primer, bonding agent, and cementitious plaster.
Perform the tiling after 4 days of smoothing the surface.
A notched trowel can help control the amount and thickness of adhesive needed for the tile installation.
The adhesive must have the proper consistency for tile installation.
The consistency should be such that the adhesive adheres to the tile immediately and does not easily separate.
In standard temperature and humidity conditions, the maximum working time is 20 minutes.
When using tiles with low absorption or larger sizes, the installation time may increase.
When tiling on a large surface, it’s essential to proceed with the installation in stages, allowing enough time between steps so that the lower part of the tile adhesive is partially dry, which helps in supporting the weight of new heavy tiles.
It is not recommended to use this adhesive in temperatures below 5°C.
The ideal temperature for drying the adhesive is above 15°C.
If the surface layer of the adhesive has dried, reapply the trowel before installing the tile.
It is necessary to apply pressure in a twisting motion to the tile after installation to ensure that the adhesive completely transfers to the back of the tile.
Grouting should be done one day after the adhesive has set.
| Feature | Value |
|---|---|
| Physical State | Powder (Solid) |
| Color | White and Gray |
| Specific Gravity | ±1.5 kg/lit |
| Mixability | Water-Soluble |
| pH | Alkaline |
| Chloride Content | None |
| Test Type | Standard | Result |
|---|---|---|
| Initial Bond Strength After 30 Minutes | EN 1348 | N/mm² ≥ 0.5 |
| Initial Tensile Bond Strength | EN 1348 | N/mm² ≥ 0.5 |
| Tensile Bond Strength After Heat Aging | EN 1348 | N/mm² ≥ 0.5 |
| Tensile Bond Strength After Water Immersion | EN 1348 | N/mm² ≥ 0.5 |
| Tensile Bond Strength After Freeze-Thaw Cycle | EN 1348 | N/mm² ≥ 0.5 |
| Open Time | EN 1346 | 20 minutes |
The powdered tile adhesive for flooring is available in 20 kg bags.
Shelf Life: When stored properly in a dry, enclosed environment and in its original packaging, the product is suitable for storage up to 6 months.
Storage Temperature: The ideal temperature range for storage is between 10°C and 35°C.
Storage Conditions: Store away from moisture, humidity, and direct sunlight exposure.
The powdered tile adhesive does not contain hazardous materials that pose a threat to health or the environment. However, it should never be ingested or come into contact with the eyes. In case of accidental contact with skin or eyes, rinse immediately with plenty of clean water.
With the development of the construction industry, the traditional mortar of cement and sand has been replaced by inorganic cement, graded silica sand, and dispersive polymers, which offer better and more cost-effective bonding for tiles and ceramics. The floor tile adhesive (C-50) contains Portland cement along with polymer additives, bonding enhancers, mineral fillers, and fibers. It is used for installing various types of tiles, ceramics, stones, etc., both indoors and outdoors. This product is fully waterproof, has very high adhesion, and after drying and curing, it will not dissolve in water. Additionally, it has waterproofing properties. This product is a single-component adhesive specifically designed for bonding floor tiles and stones.
This product complies with EN 12004-TYPE C1E standards.
Qom, Mahmoudabad Industrial Town, Phase 3, Resalat Street, Alley 42
09909142925 | 09909142924
